联系济南太阳集团y8722ycc|集团欢迎您 / Contact us

济南太阳集团y8722ycc|集团欢迎您

客户咨询热线

0531-85767688

售后热线:15668327566

联系基地:山东省 德州市协同发展产业园D06幢

安装支架高度标准有哪些?

文章来源:/   作者:电缆桥架厂家发布时间:2023-08-07 浏览次数:40

返回:行业动态
安装支架安装高度可在2.2-2.8米范围内可调,选择2.2米时应防止人为拆除破坏,选择2.8 米时注意通风管等其他物品影响视频探测器视野。安装支架水平距离车位线可在3-4米范围内可调,双车位时候选择行车道(宽度)中间位置。本安装支架应为车场吊装设备低安装位置。在有坡度的场所安装安装支架时,安装支架坡度宜与建筑物一致。在有圆弧形的建筑物安装安装支架, 其圆弧宜一致。安装支架应“横屏竖直”,安装支架安装完成应用水平尺测量安装支架符合水平要求,使用激光投线 仪确认安装支架是否在一条直线上。
The installation height of the mounting bracket can be adjusted within the range of 2.2-2.8 meters. When selecting 2.2 meters, it is important to prevent human demolition and damage. When selecting 2.8 meters, it is important to pay attention to ventilation pipes and other items that may affect the visual field of the video detector. The horizontal distance between the installation bracket and the parking space line can be adjusted within a range of 3-4 meters. When using dual parking spaces, choose the middle position of the lane (width). This installation bracket should be the lowest installation position for the lifting equipment in the parking lot. When installing brackets in sloping areas, the slope of the installation bracket should be consistent with the building. Install brackets in buildings with circular arcs, and the arcs should be consistent. The installation bracket should be "horizontally and vertically". After the installation of the bracket is completed, use a horizontal ruler to measure whether the bracket meets the horizontal requirements. Use a laser projector to confirm whether the bracket is in a straight line.
设备安装完成再次确定安装支架高度与水平距离车位的宽度。 支吊架的选择? 安装支架安装选用的支吊架为一下几种:双拉通丝吊架、单拉通丝吊架、角铁支架。双拉通丝吊架由通杆螺丝、拉爆、横梁组成,双拉通丝吊架每一个吊架选用两个通杆螺 丝组成。单拉通丝吊架由通杆螺丝、拉爆、吊框组成,单拉通丝吊架每一个吊架选用一个通杆螺 丝组成。角铁支架,分为U型支架、L型支架。其主要材质为角铁,作用为固定安装支架,确保桥 架不会随意晃动?单拉通丝吊架如下图使用卷尺,确认地面点位。根据视频车位引导系统视频探测器的安装要求,即视频探测器距离车位线前方位置3米,当车位为相对应的车位时候,安装支架应当选择在车辆行驶道路的中间位置。
Once the equipment installation is completed, determine the height of the installation bracket and the width of the horizontal distance from the parking space again. The selection of supports and hangers? The following types of supports and hangers are selected for the installation of brackets: double pull through wire hangers, single pull through wire hangers, and angle iron brackets. The double pull through wire hanger is composed of through rod screws, pull-out bolts, and crossbeams. Each hanger of the double pull through wire hanger is composed of two through rod screws. The single pull through wire hanger is composed of a through rod screw, a pull-out bolt, and a hanging frame. Each hanger of the single pull through wire hanger is composed of a through rod screw. Angle iron brackets are divided into U-shaped brackets and L-shaped brackets. Its main material is angle iron, which serves as a fixed installation bracket to ensure that the bridge does not shake at will? Use a tape measure to confirm the ground position of the single pull through wire hanger as shown in the figure below. According to the installation requirements of the video detector in the video parking guidance system, the video detector should be located 3 meters in front of the parking line. When the parking space is the corresponding parking space, the installation bracket should be selected in the middle of the vehicle's driving road.
1.使用“激光投线仪”确认顶棚通杆螺丝的位置,并使用电钻进行开孔。上图激光投线仪,确认安装支架支吊架位置。
1. Use the "laser line projector" to confirm the position of the ceiling through rod screws and use an electric drill for drilling. Confirm the position of the installation bracket support and hanger for the laser line projector shown above.
2.安装支架支吊架间距为3米,在直线与弯通连接处0.3米的位置使用吊架。安装支架的安装高度为2.5米。
2. Install brackets with a spacing of 3 meters between supports and hangers, and use hangers at a position of 0.3 meters at the connection between straight lines and bends. The installation height of the bracket is 2.5 meters.
3.根据现场地面与顶棚的高度计算通杆螺丝的长度,并使用切割机进行切割处理。注:确认通杆螺丝位置时建议比原来长度稍长几公分确保可以小幅度调整安装支架水平位置。 五、使用拉爆与通杆螺丝相结合将通杆螺丝固定在顶棚确定的位置,并在通杆螺丝的下端安装吊框,吊框选用安装支架厂商提供的原件。
3. Calculate the length of the through rod screw based on the height of the ground and ceiling on site, and use a cutting machine for cutting treatment. Note: When confirming the position of the through rod screw, it is recommended to slightly extend the original length by a few centimeters to ensure that the horizontal position of the installation bracket can be adjusted slightly. 5、 Use a combination of pull-out and through-pole screws to fix the through-pole screws at the designated position on the ceiling, and install a hanging frame at the lower end of the through-pole screws. The hanging frame is selected from the original components provided by the installation bracket manufacturer.
济南电缆桥架
4.安装支架组装与安装安装支架的直线段之间连接使用厂商提供的连接件。安装支架应当在建筑物伸缩出设置安装支架伸缩 缝。具体办法:安装支架连接处一端安装支架连接片上螺丝不上即可安装支架直线段安装时,直接将安装支架穿过吊框,连接缝使用联接片连接。
4. The connection between the assembly of the installation bracket and the straight section of the installation bracket shall be made using the connection pieces provided by the manufacturer. The installation bracket should be equipped with expansion joints at the expansion point of the building. Specific method: Install the bracket at one end of the bracket connection point. If the screw on the bracket connection piece is not tightened, the bracket can be installed. When installing the straight section of the bracket, directly pass the installation bracket through the hanging frame, and use the connection piece to connect the connection seam.
5.并安装跨界软铜线:安装支架位置矫正与检查确保安装支架安装完成之后处于水平位置,如不符合要求应当立即进行调整。确保安装支架前端与后端处于同一直线上,如不符合要求立即进行调整。
5. Install crossover flexible copper wire: Correct and inspect the position of the installation bracket to ensure that it is in a horizontal position after installation. If it does not meet the requirements, it should be adjusted immediately. Ensure that the front and rear of the installation bracket are in the same straight line, and adjust immediately if they do not meet the requirements.
6.确保安装支架连接处应有软通线连接,如没有应当立即增加。确保安装支架某一直线段起始端与末端应当有角铁加进行固定,安装支架超过一定距离时应当选用角铁支架进行固定。确保安装支架距离地面高度一致,如不符合要求立即进行调整。确保安装支架距离车位线位置符合设计要求,如不符合要求立即进行调整。
6. Ensure that there should be a flexible cable connection at the connection point of the installation bracket. If not, it should be added immediately. Ensure that the starting and ending ends of a certain line segment of the installation bracket should be fixed with angle iron brackets. When the installation bracket exceeds a certain distance, angle iron brackets should be selected for fixation. Ensure that the installation bracket is at the same height from the ground, and adjust it immediately if it does not meet the requirements. Ensure that the distance between the installation bracket and the parking line meets the design requirements. If it does not meet the requirements, adjust it immediately.
本文由山东电缆桥架友情奉献.更多有关的知识请点击:真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.
This article is dedicated by Shandong Cable Bridge Friendship. For more relevant knowledge, please click on: Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned
工程案例 / Case Show
  • 济南火车站 济南火车站
  • 曲阜孔子文化会展中心 曲阜孔子文化会展中心
  • 山东工艺美院 山东工艺美院
  • 公安厅服务展示 公安厅服务展示